{"product_id":"gomagom-32-powertack-exterior-20g","title":"Gomagom 32 PowerTack 20g | Reusable Adhesive Putty \"Blu-Tack\" Style for 3D Figures and Miniatures","description":"\u003cp\u003eGomagom 32 PowerTack Exterior is a reusable adhesive putty in red square portions, 20 g, combining two properties that make it particularly useful for 3D printing workshops and scale modeling: \u003cstrong\u003e3 times stronger\u003c\/strong\u003e than standard adhesive putties (like the classic blue Blu Tack) and \u003cstrong\u003ewater and UV resistant\u003c\/strong\u003e, so it holds up under conditions that would cause a standard soft adhesive to fail. Peel it off, knead it with your fingers, press it wherever you need to secure something, and it stays put until you decide to remove it — leaving no residue and reusable dozens of times. Perfect for miniature painting, holding printed parts during post-processing, or home and office tasks that require temporary fixing without drilling or damaging surfaces.\u003c\/p\u003e\n\n\u003ch2\u003eWhy miniature painters choose this putty\u003c\/h2\u003e\n\u003cp\u003eAnyone who paints wargaming miniatures (Citadel, Vallejo, Army Painter, or their own 3D prints) has been using Blu Tack-style adhesive putty for years. It's the standard way to mount a miniature on a painting handle, hold a small piece while painting it separately, or create temporary airbrush masks. The problem with traditional Blu Tack is that it \u003cstrong\u003ebreaks down with spray primer, varnish, and moisture\u003c\/strong\u003e, leaves residue on painted pieces, and can't support the weight of large busts or dense resin-printed terrain.\u003c\/p\u003e\n\u003cp\u003eGomagom 32 PowerTack Exterior solves all three problems: the exterior-grade formula resists water, isopropyl alcohol (used for washing UV resin prints), aerosols, and UV exposure without degrading. And being 3x stronger than standard Blu Tack, it holds pieces with real weight — a 75 mm bust printed in dense UV resin, large modular terrain, a 28 mm scale wargaming helmet, and more.\u003c\/p\u003e\n\n\u003ch2\u003eUse cases in miniature painting and 3D printing\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eMounting miniatures on DIY painting handles.\u003c\/strong\u003e Press a small ball onto a wine cork, a wooden dowel, or a commercial painting handle. The miniature stays secure throughout the entire session and comes off cleanly when you're done. Reusable: the same piece works for dozens of different miniatures.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHolding small parts for separate painting.\u003c\/strong\u003e When assembling a kit in sub-assemblies before painting (shields, backpacks, weapons, heads, accessories), PowerTack lets you fix each piece to a holder while you paint it, without touching it with your fingers.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTemporary airbrush masking.\u003c\/strong\u003e To cover areas you don't want painted (a miniature's face while painting the armor, a gold area while painting the rest), apply PowerTack and peel it off once done — it withstands standard hobby aerosols without dissolving.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePropping printed parts during curing.\u003c\/strong\u003e To hold a freshly glued piece in a position it can't support on its own while cyanoacrylate or epoxy putty sets. Especially useful when assembling 3D printed parts with angled or irregular contact surfaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSecuring UV resin prints during post-processing.\u003c\/strong\u003e To fix a piece to the work surface during sanding, support removal, or painting, without the risk of clamp deformation. Handles isopropyl alcohol from washing and uncured resin residue better than standard Blu Tack.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMiniature and model photography.\u003c\/strong\u003e To hold a piece in exactly the position you want to photograph, with no visible support. A minimal amount hidden behind the base solves the problem.\u003c\/p\u003e\n\n\u003ch2\u003eOther uses: home, office, and DIY\u003c\/h2\u003e\n\u003cp\u003eBeyond the world of miniatures and 3D printing, PowerTack fills the classic role of reusable adhesive putty, with the added benefit of its exterior-grade durability:\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHanging posters, photos, and signs.\u003c\/strong\u003e No nails, no pins, no wall damage. Perfect for rental spaces or any surface you don't want to mark up. Its UV resistance means it holds better than standard adhesive putty in areas with direct sunlight.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSecuring items in garages, workshops, or humid environments.\u003c\/strong\u003e Where regular adhesive putty would eventually fail. Great for hanging labels, laminated instructions, 3D printer build plates, and parameter cheat sheets next to your equipment.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuick fixes and temporary holds.\u003c\/strong\u003e When you need something to stay put for a few hours or days but want a clean, residue-free removal. Far neater than double-sided tape for temporary applications.\u003c\/p\u003e\n\n\u003ch2\u003eHow to Use\u003c\/h2\u003e\n\u003cp\u003eThe manufacturer's process is straightforward:\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e1. Peel off the amount you need and roll it into a ball.\u003c\/strong\u003e PowerTack comes in pre-scored square portions — peel off as many as you need based on the size of what you're mounting. A single portion is enough for small miniatures; for heavier applications (large busts, terrain pieces), combine several portions together.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e2. Knead with your fingers until the putty is warm and pliable.\u003c\/strong\u003e The heat from your hands softens it and improves initial adhesion.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3. Apply to the back of the object and press firmly.\u003c\/strong\u003e Initial tack is immediate, but maximum holding strength builds over time — the manufacturer states this explicitly: \"Adhesive qualities increase with time.\"\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e4. To remove: gently twist the surfaces apart.\u003c\/strong\u003e Do NOT pull straight off. The twisting motion breaks the bond cleanly without leaving residue on non-porous surfaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eImportant: surfaces where PowerTack should NOT be used.\u003c\/strong\u003e The manufacturer explicitly advises against use on absorbent surfaces (porous foam board, paper), delicate finishes, or surfaces that are wet, dusty, or freshly painted. Before using on a prized painted miniature, we recommend testing on a hidden area first — PowerTack has a strong hold, and on fragile or very recent paintwork it may lift paint when removed.\u003c\/p\u003e\n\n\u003ch2\u003eLifespan and Storage\u003c\/h2\u003e\n\u003cp\u003eThe putty is reusable across many cycles. Actual lifespan depends on use: if you're using it to hold miniatures for painting and it only contacts clean, dry surfaces, it can last months or over a year. If it's used in applications where it picks up dust, paint residue, or fine particles, the surface gradually becomes contaminated and loses grip — in that case, peel away the outer layer with your fingers to expose a fresh active surface, or discard that portion and use a new piece from the pack.\u003c\/p\u003e\n\u003cp\u003eStore at room temperature in a dry place. It leaves no residue on non-porous surfaces, but always remove with a twisting motion to avoid any marks after extended contact.\u003c\/p\u003e\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Reusable adhesive putty (Blu Tack style), outdoor\/exterior formula\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNet weight:\u003c\/strong\u003e 20 g (declared with ℮ symbol)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Red\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFormat:\u003c\/strong\u003e Sheet of pre-scored square portions\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAdhesive strength:\u003c\/strong\u003e 3× stronger than standard adhesive putty\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eResistance:\u003c\/strong\u003e Water and UV resistant\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eReusable:\u003c\/strong\u003e Yes, across dozens of uses\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eResidue:\u003c\/strong\u003e Leaves no residue on non-porous surfaces when removed correctly with a twisting motion\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTypical hobby\/miniature uses:\u003c\/strong\u003e Securing miniatures to painting handles, temporary masking for airbrushing, holding small parts during painting, securing resin-printed pieces during post-processing\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGeneral uses:\u003c\/strong\u003e Hanging posters and signs, temporary fixing at home\/office\/workshop, temporary repairs\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDO NOT use on:\u003c\/strong\u003e Absorbent, delicate, wet, dusty, or freshly painted surfaces\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eWarning:\u003c\/strong\u003e Not suitable for children under 36 months (contains small parts)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e DUNSA (Gomagom brand, Spain)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eReference:\u003c\/strong\u003e SKU 15023\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eWhy Buy It from Mr Resin\u003c\/h2\u003e\n\u003cp\u003eIf you paint wargaming miniatures or 3D printed parts on a regular basis, a sheet of PowerTack is one of those consumables that lasts a long time and solves problems every day — from the painting session to photographing the finished piece. Standard blue Blu Tack works up to a point, but it breaks down with the first coat of primer spray and can't hold heavier pieces. The EXTERIOR version of the Gomagom 32 handles those demanding situations.\u003c\/p\u003e\n\u003cp\u003eIf you're already ordering resin, filament, or paint, adding the PowerTack ships in the same package at no extra cost. Free shipping to mainland Spain on orders over €79.\u003c\/p\u003e\n\u003cp\u003eMr Resin has been serving over 5,000 makers across Spain, Portugal, and France for years. Our catalog is built around what the community asks for: printers and materials at its core, plus the workshop consumables that become part of your everyday workflow.\u003c\/p\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it to attach miniatures to a painting handle?\u003c\/strong\u003e\u003cbr\u003e\nYes, this is one of its best use cases. A small portion on top of a cork or commercial holder is enough to secure a miniature throughout an entire painting session. The bond holds through hours of handling, and the figure releases cleanly when you're done — no residue left behind as long as you remove it with a twisting motion. The key advantage over standard Blu Tack is that it holds up to primer and varnish sprays without losing its grip.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eIs it compatible with primer and varnish sprays?\u003c\/strong\u003e\u003cbr\u003e\nYes. As an outdoor-formula putty with water and UV resistance, it also withstands the aerosols commonly used in miniature painting: spray primers, matte\/satin\/gloss varnishes, and lacquers. Where standard Blu Tack absorbs moisture from the spray and loses its hold, PowerTack maintains adhesion throughout. This makes it particularly useful as a temporary mask for airbrushing.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eCan it hold the weight of a large miniature or resin-printed terrain piece?\u003c\/strong\u003e\u003cbr\u003e\nYes, within a reasonable range. The manufacturer rates it at 3× the adhesive strength of standard putty, which in practice means it can securely hold dense UV resin busts at 75 mm scale, medium-sized modular terrain, and 28–32 mm scale miniatures without issue. For very heavy pieces (large busts over 200–300 g, plaster-based dioramas), we recommend using multiple portions combined or switching to mechanical fastening.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many times can it be reused?\u003c\/strong\u003e\u003cbr\u003e\nDozens of times, depending on how it's used. If it only comes into contact with clean surfaces (washed hands, dust-free miniatures, dry supports), it can last months or even over a year with regular use. If it picks up dust or paint residue over time, the surface becomes contaminated and gradually loses its grip — in that case, simply peel away the outer layer with your fingers to expose fresh putty underneath.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eDoes it leave marks or residue on painted miniatures?\u003c\/strong\u003e\u003cbr\u003e\nOn properly painted surfaces with a fully cured finish (well-dried acrylics, fully set primer), it leaves no residue as long as you remove it with a gentle twisting motion rather than pulling straight off. On very fresh or fragile finishes (paint applied the same day, partially cured varnish), there is a risk of lifting paint. As a general rule: make sure the miniature is fully dry before applying PowerTack, and test on a hidden area first if the piece is valuable.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eCan it be used with 3D printers?\u003c\/strong\u003e\u003cbr\u003e\nIn the literal sense — securing prints to the build plate or shimming the FEP — it's not recommended: there are purpose-built products for those applications. Where it does work very well is in post-processing: holding printed parts to your work surface while sanding, removing supports, or painting, without the risk of deformation that a clamp might cause. It's a workshop tool, not part of the printing process itself.\u003c\/p\u003e","brand":"GomaGom","offers":[{"title":"Default Title","offer_id":53860240654673,"sku":"15023","price":4.34,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0852\/0414\/0369\/files\/GomaGom_masilla_adhesiva_blu_tack_para_miniaturas_e_impresion_3D.jpg?v=1780215492","url":"https:\/\/mrresin.es\/en\/products\/gomagom-32-powertack-exterior-20g","provider":"Mr Resin","version":"1.0","type":"link"}