{"product_id":"heygears-rascador-calefactado-reflex-2","title":"HeyGears Reflex 2 \/ 2 Pro - Heated Resin Scraper","description":"\u003ch2\u003eHeyGears Heated Scraper for Reflex 2 and Reflex 2 Pro\u003c\/h2\u003e\n\u003cp\u003eThe Reflex 2 series scraper is the part that moves across the vat, stirring the resin between layers. The heated version has a built-in heater and temperature sensor: it warms the resin while stirring it and keeps it at printing temperature throughout the entire job. The Reflex 2 Pro comes with it as standard; the Reflex 2 comes with the regular scraper, and this is its optional temperature-control upgrade.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible with:\u003c\/strong\u003e Reflex 2 and \u003ca href=\"https:\/\/mrresin.es\/en\/products\/impresora-3d-heygears-ultracraft-reflex-2-pro\"\u003eReflex 2 Pro\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFaster heating:\u003c\/strong\u003e from 10 °C to 22 °C in 6 minutes, 68 % faster according to HeyGears (tested with PAP10).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature control:\u003c\/strong\u003e ±1 °C.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaintains the temperature\u003c\/strong\u003e throughout the entire print.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrip time:\u003c\/strong\u003e 24 % less waiting with high-viscosity resins (HeyGears data with PAU20).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat it's for\u003c\/h3\u003e\n\u003cp\u003eCold resin is thicker: it drains more poorly, struggles to flow under the build plate and causes more print failures. HeyGears recommends printing between 20 and 25 °C. If your workshop gets cold in winter, or you use thick engineering resins, the heated scraper brings the resin up to temperature without waiting for the room to warm up. Stirring also keeps the resin from settling and leaving residue in the vat.\u003c\/p\u003e\n\u003cp\u003eHeyGears data:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWith PAP10, from 10 °C to 22 °C in 6 minutes.\u003c\/li\u003e\n\u003cli\u003eWith PAU20 at 50 µm layers, heating from 25 °C to 35 °C reduced drip waiting time by more than 24 % on models with a cross-section larger than 40 mm.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eReflex 2:\u003c\/strong\u003e optional upgrade. The printer comes with the regular scraper.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReflex 2 Pro:\u003c\/strong\u003e included as standard. This one serves as a replacement or spare part.\u003c\/li\u003e\n\u003cli\u003eFits the Reflex 2 series vat. The Reflex 2 Pro comes with it as standard and supports the Pulsing Release Module 2 kit, so it also works with the Pulsing Release vat.\u003c\/li\u003e\n\u003cli\u003eNot compatible with the Reflex, Reflex Turbo or the Reflex RS family. On the RS, heating is handled by the \u003ca href=\"https:\/\/mrresin.es\/en\/products\/heygears-tanque-pulsing-release-reflex-rs\"\u003eheated vat\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eInstallation and use\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIt fits into the vat just like the regular scraper, after installing the vat and the build plate.\u003c\/li\u003e\n\u003cli\u003eBefore levelling the build plate, the scraper must be at the far right end of the vat. If it doesn't return on its own, move it there by hand.\u003c\/li\u003e\n\u003cli\u003eDo not disconnect it while it is moving or heating.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCleaning\u003c\/h3\u003e\n\u003cp\u003eHeyGears' procedure for the Reflex 2 series scraper:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eUse a container of about 215 x 145 mm or slightly longer than the scraper.\u003c\/li\u003e\n\u003cli\u003eDip only the part that goes inside the vat into 95 % alcohol or IPA. The back of the scraper must not touch the liquid.\u003c\/li\u003e\n\u003cli\u003eHold it by the end and move it from side to side to clean it.\u003c\/li\u003e\n\u003cli\u003eDry the scraper's holes with compressed air and repeat if any resin remains.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eAlcohol and cleaning supplies in \u003ca href=\"https:\/\/mrresin.es\/en\/collections\/alcohol-and-post-processing\"\u003epost-processing\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eReflex 2 Series Heating Scraper\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTemperature accuracy\u003c\/td\u003e\n\u003ctd\u003e±1 °C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHeating\u003c\/td\u003e\n\u003ctd\u003e10 °C to 22 °C in 6 min (PAP10)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompatibility\u003c\/td\u003e\n\u003ctd\u003eReflex 2, Reflex 2 Pro\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEAN\u003c\/td\u003e\n\u003ctd\u003e6971437944073\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eWhich one should you choose?\u003c\/h3\u003e\n\u003cp\u003eIf you have a Reflex 2 and your workshop stays above 20 °C all year round, the regular scraper is all you need. If you work in a cold space or use thick resins such as PAU20, the heated one is the upgrade for you. With the Reflex 2 Pro, you only need it as a spare part.\u003c\/p\u003e\n\n\u003ch3\u003eWho it's not for\u003c\/h3\u003e\n\u003cp\u003eIt's not for the original Reflex, the Reflex Turbo, the RS or the RS Turbo, nor for printers from other brands.\u003c\/p\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eDoes the Reflex 2 Pro already include it?\u003c\/h4\u003e\n\u003cp\u003eYes, the Reflex 2 Pro comes with a heated scraper. The Reflex 2 comes with the regular one.\u003c\/p\u003e\n\u003ch4\u003eHow long does it take to heat the resin?\u003c\/h4\u003e\n\u003cp\u003eAccording to HeyGears, from 10 °C to 22 °C in 6 minutes with PAP10.\u003c\/p\u003e\n\u003ch4\u003eHow accurate is it?\u003c\/h4\u003e\n\u003cp\u003e±1 °C.\u003c\/p\u003e\n\u003ch4\u003eDoes it work with the Pulsing Release vat?\u003c\/h4\u003e\n\u003cp\u003eIt fits the Reflex 2 series vat. HeyGears does not indicate any limitation with the Pulsing Release vat.\u003c\/p\u003e\n\u003ch4\u003eIs it compatible with the Reflex RS?\u003c\/h4\u003e\n\u003cp\u003eNo. On the RS, the resin is heated by the heated vat.\u003c\/p\u003e\n\u003ch4\u003eHow do I clean it?\u003c\/h4\u003e\n\u003cp\u003eOnly the part that goes in the vat, in 95 % alcohol or IPA, without wetting the back. Then blow compressed air through the holes.\u003c\/p\u003e\n\u003ch4\u003eCan I remove it with the printer switched on?\u003c\/h4\u003e\n\u003cp\u003eNot while it is moving or heating.\u003c\/p\u003e","brand":"HeyGears","offers":[{"title":"Default Title","offer_id":55384204542289,"sku":"DIST-6971437944073","price":93.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0852\/0414\/0369\/files\/heygears-rascador-calefactado-reflex-2.jpg?v=1792509564","url":"https:\/\/mrresin.es\/en\/products\/heygears-rascador-calefactado-reflex-2","provider":"Mr Resin","version":"1.0","type":"link"}