{"product_id":"heygears-tanque-pulsing-release-reflex-rs","title":"HeyGears Reflex RS Heated \u0026 Pulsing Release Resin Tank - Heated Pulsing Release Tank for Reflex RS and RS Turbo","description":"\u003ch2\u003eHeyGears Heated \u0026amp; Pulsing Release Resin Tank for Reflex RS and RS Turbo\u003c\/h2\u003e\n\u003cp\u003eHeyGears calls it the \u003cem\u003eReflex RS Heated \u0026amp; Pulsing Release Resin Tank\u003c\/em\u003e, and it's a 2-in-1 tank: it heats the resin on its own and, if you have the Pulsing Release Module, it also handles pulsed peeling. On the Reflex RS and the \u003ca href=\"https:\/\/mrresin.es\/en\/products\/impresora-3d-heygears-ultracraft-reflex-rs-turbo\"\u003eReflex RS Turbo\u003c\/a\u003e, it's also the only tank that works with automatic resin heating.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible with:\u003c\/strong\u003e Reflex RS and Reflex RS Turbo.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt-in heating:\u003c\/strong\u003e brings the resin from 10 °C to 22 °C in about 20 minutes and keeps it there throughout the print (HeyGears figure).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePulsing Release:\u003c\/strong\u003e only with the Pulsing Release Module connected.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks without the module too:\u003c\/strong\u003e as a standard heated tank.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow Pulsing Release works\u003c\/h3\u003e\n\u003cp\u003eThe module periodically inflates and deflates the tank film. This cycle of positive and negative pressure reduces the peel force of each layer by around 50 %. According to HeyGears, with PAS10 this means between 20 % and 60 % fewer supports and between 25 % and 54 % less contact area.\u003c\/p\u003e\n\n\u003ch3\u003eCompatibility and Pulsing Release Module\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eWith the module:\u003c\/strong\u003e connect the Pulsing Release Module and select the module when slicing in Blueprint Studio. The \u003ca href=\"https:\/\/mrresin.es\/en\/products\/heygears-pulsing-release-module-kit-reflex-rs\"\u003ePulsing Release Module kit for Reflex RS\u003c\/a\u003e already includes a tank like this one; this standalone tank works as a second tank or a replacement.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWithout the module:\u003c\/strong\u003e in Blueprint Studio, select \"No Add-on Module\" and the RS will enable heating automatically.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eResins compatible with the module on the RS:\u003c\/strong\u003e HeyGears lists PARP10, PAS10, PAP10, PAWR10, PAF10 and PAU11. The water-washable resins PAWW10 and PAWW20 are not compatible with the module.\u003c\/li\u003e\n\u003cli\u003eHeyGears does not recommend using the module for models with walls of 3 mm or less.\u003c\/li\u003e\n\u003cli\u003eNot compatible with the Reflex, Reflex Turbo or the Reflex 2 series: each family has its own tank.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhen to replace it or get a second one\u003c\/h3\u003e\n\u003cp\u003eThe film and the tank don't have the same lifespan: if only the film fails, replace it with the Pulsing Release film set for Reflex RS. Replace the complete tank if the frame gets damaged or if you want one tank per resin so you don't have to keep emptying it.\u003c\/p\u003e\n\n\u003ch3\u003eMaintenance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eCheck the resin before and after every print. A leftover cured fragment can tear the film when the platform lowers.\u003c\/li\u003e\n\u003cli\u003eTo clean out residue, use the \u003cem\u003eResin Tank Cleaning\u003c\/em\u003e function and the residue tool that comes with the printer. Don't pull cured resin off by hand.\u003c\/li\u003e\n\u003cli\u003eThe official installation videos for the tank and the module on the RS are available on the HeyGears wiki.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich one should you choose?\u003c\/h3\u003e\n\u003cp\u003eThe standard Reflex RS tank is cheaper, but it doesn't heat and doesn't support the module. If you print in a cold workshop or want to try Pulsing Release later on, this is the one to get.\u003c\/p\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eDo I need the Pulsing Release Module to use it?\u003c\/h4\u003e\n\u003cp\u003eNo. Without the module, it works as a heated tank when you select \"No Add-on Module\" in Blueprint Studio.\u003c\/p\u003e\n\u003ch4\u003eDoes the standard RS tank heat the resin?\u003c\/h4\u003e\n\u003cp\u003eNo. HeyGears states that automatic heating on the RS requires this tank.\u003c\/p\u003e\n\u003ch4\u003eDoes it work on the Reflex or Reflex Turbo?\u003c\/h4\u003e\n\u003cp\u003eNo. For those printers, there's the \u003ca href=\"https:\/\/mrresin.es\/en\/products\/heygears-tanque-pulsing-release-reflex\"\u003ePulsing Release tank for Reflex\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch4\u003eCan I use PAWW10 or PAWW20?\u003c\/h4\u003e\n\u003cp\u003eNot with the module active. HeyGears lists them as not compatible with the Pulsing Release Module.\u003c\/p\u003e\n\u003ch4\u003eCan the film be replaced on its own?\u003c\/h4\u003e\n\u003cp\u003eYes, it's sold separately in a pack of two.\u003c\/p\u003e\n\u003ch4\u003eHow long does it take to heat up?\u003c\/h4\u003e\n\u003cp\u003eAccording to HeyGears, from 10 °C to 22 °C in about 20 minutes.\u003c\/p\u003e","brand":"HeyGears","offers":[{"title":"Default Title","offer_id":55384203329873,"sku":"DIST-6971437942109","price":234.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0852\/0414\/0369\/files\/heygears-tanque-calefactado-pulsing-release-reflex-rs_313ec633-db7e-45ab-890a-56e38bc91cfc.jpg?v=1792509545","url":"https:\/\/mrresin.es\/en\/products\/heygears-tanque-pulsing-release-reflex-rs","provider":"Mr Resin","version":"1.0","type":"link"}