{"product_id":"resina-heygears-ultraprint-casting-pac10-calcinable-1kg","title":"HeyGears UltraPrint Casting PAC10 - Castable Wax Resin for Jewelry 385 nm 1 kg","description":"\u003ch2\u003eHeyGears UltraPrint Casting PAC10: wax-filled castable resin for jewellery (385 nm)\u003c\/h2\u003e\n\u003cp\u003eUltraPrint-Casting PAC10 is HeyGears' resin for printing lost-wax casting patterns. It contains 70 to 75 % wax, leaves no more than 0.02 % ash and burns out cleanly inside the flask. The pattern comes off the printer, goes onto the tree, gets invested and is cast in metal just like a wax pattern. HeyGears shows castings in silver, gold and copper. Violet colour, 1 kg bottle.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBefore you buy: this is a 385 nm resin only for HeyGears UltraCraft Reflex printers and it requires the Pulsing Release Module.\u003c\/strong\u003e It does not work on 405 nm LCD printers from other brands (Elegoo, Anycubic, Phrozen, Creality...) or on the Reflex RS \/ RS Turbo. If you have a different printer, check out our \u003ca href=\"https:\/\/mrresin.es\/collections\/resinas-calcinables\"\u003ecastable resins\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eWax content:\u003c\/strong\u003e 70-75 %.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAsh after burnout:\u003c\/strong\u003e 0.01-0.02 % (thermogravimetric analysis, ASTM E1131).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFine detail:\u003c\/strong\u003e 0.08 mm engraved and 0.12 mm embossed details. Minimum wall thickness of 0.12 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTolerance:\u003c\/strong\u003e ±0.03 mm on parts up to 20 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBurnout schedule published\u003c\/strong\u003e by HeyGears for gypsum-bonded investments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWavelength:\u003c\/strong\u003e 385 nm only. Requires the Pulsing Release Module.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat it's for\u003c\/h3\u003e\n\u003cp\u003eHeyGears designed it for jewellery and small precision casting parts:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLightweight jewellery:\u003c\/strong\u003e rings, earrings and pendants, including openwork or lattice designs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDetailed parts:\u003c\/strong\u003e stud earrings, setting prongs, textures and engravings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeavy jewellery:\u003c\/strong\u003e bracelets and solid rings.\u003c\/li\u003e\n\u003cli\u003eSmall lost-wax industrial parts.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIt offers a good balance of toughness and strength for a castable material. That matters for openwork and hollow patterns, which break when removing supports or building the tree if the wax is brittle.\u003c\/p\u003e\n\u003cp\u003eDo you work in dental prosthetics? Dental labs use the same lost-wax technique, but HeyGears does not list PAC10 as a certified dental material. For that, check out our \u003ca href=\"https:\/\/mrresin.es\/collections\/resinas-dentales\"\u003edental resins\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eCompatibility: which printers it works with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrinters:\u003c\/strong\u003e UltraCraft Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot compatible\u003c\/strong\u003e with the Reflex RS \/ RS Turbo.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePulsing Release Module required.\u003c\/strong\u003e For Reflex and Reflex Turbo, the \u003ca href=\"https:\/\/mrresin.es\/products\/heygears-pulsing-release-module-kit-reflex\"\u003ePulsing Release Module Kit Reflex\u003c\/a\u003e. For Reflex 2 and 2 Pro, the \u003ca href=\"https:\/\/mrresin.es\/products\/heygears-pulsing-release-module-kit-reflex-2\"\u003ePulsing Release Module Kit Reflex 2\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIf you're looking for a printer, the \u003ca href=\"https:\/\/mrresin.es\/products\/impresora-3d-heygears-ultracraft-reflex-turbo\"\u003eUltraCraft Reflex Turbo\u003c\/a\u003e and the \u003ca href=\"https:\/\/mrresin.es\/products\/impresora-3d-heygears-ultracraft-reflex-2-pro\"\u003eUltraCraft Reflex 2 Pro\u003c\/a\u003e are compatible.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eProperty\u003c\/th\u003e\n\u003cth\u003eStandard\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eWax content\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003ctd\u003e70-75 %\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAsh (TGA)\u003c\/td\u003e\n\u003ctd\u003eASTM E1131\u003c\/td\u003e\n\u003ctd\u003e0.01-0.02 %\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTemperature at 5 % mass loss\u003c\/td\u003e\n\u003ctd\u003eASTM E1131\u003c\/td\u003e\n\u003ctd\u003e274 °C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTensile strength\u003c\/td\u003e\n\u003ctd\u003eASTM D638\u003c\/td\u003e\n\u003ctd\u003e21 MPa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTensile modulus\u003c\/td\u003e\n\u003ctd\u003eASTM D638\u003c\/td\u003e\n\u003ctd\u003e450 MPa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFlexural strength\u003c\/td\u003e\n\u003ctd\u003eASTM D790\u003c\/td\u003e\n\u003ctd\u003e30 MPa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFlexural modulus\u003c\/td\u003e\n\u003ctd\u003eASTM D790\u003c\/td\u003e\n\u003ctd\u003e680 MPa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eElongation at break\u003c\/td\u003e\n\u003ctd\u003eASTM D638\u003c\/td\u003e\n\u003ctd\u003e16 %\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNotched impact\u003c\/td\u003e\n\u003ctd\u003eASTM D256\u003c\/td\u003e\n\u003ctd\u003e13 J\/m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHardness\u003c\/td\u003e\n\u003ctd\u003eASTM D2240\u003c\/td\u003e\n\u003ctd\u003e64 Shore D\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eViscosity\u003c\/td\u003e\n\u003ctd\u003eASTM D4212\u003c\/td\u003e\n\u003ctd\u003e259 mPa·s\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eHeyGears laboratory data with a deviation of ±10 %.\u003c\/p\u003e\n\u003ch4\u003ePattern design rules\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eMinimum wall thickness of 0.12 mm. For 10 × 10 mm walls, HeyGears recommends 0.18-0.2 mm.\u003c\/li\u003e\n\u003cli\u003eMinimum through-hole of 0.3 mm at 2 mm depth.\u003c\/li\u003e\n\u003cli\u003e0.08 mm engraved and 0.12 mm embossed details (at 0.4 mm depth).\u003c\/li\u003e\n\u003cli\u003eMinimum clearance between moving parts: 0.25 mm.\u003c\/li\u003e\n\u003cli\u003eFor hollow parts, drain holes of 1 to 2 mm depending on size.\u003c\/li\u003e\n\u003cli\u003eTolerance: ±0.03 mm up to 20 mm, ±0.1 mm up to 50 mm and ±0.15 mm up to 100 mm.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eUse and post-processing\u003c\/h3\u003e\n\u003ch4\u003ePrinting\u003c\/h4\u003e\n\u003cp\u003eShake the bottle well before use and stir the resin in the vat. If you won't be printing for 3 days, filter it and pour it back into the bottle. Don't leave it in the vat for more than 7 days, as it absorbs moisture. In jewellery, surface finish is everything: the first time, print with Blueprint's default supports and add plenty of supports on low points and islands.\u003c\/p\u003e\n\u003ch4\u003eWashing\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003e95 % alcohol or IPA: 1-minute initial wash in used alcohol and a 2-minute rinse in clean alcohol.\u003c\/li\u003e\n\u003cli\u003eIn the \u003ca href=\"https:\/\/mrresin.es\/products\/heygears-ultracraft-wash-estacion-de-lavado\"\u003eUltraCraft Wash\u003c\/a\u003e at 160 rpm, or in an ultrasonic cleaner with the same times.\u003c\/li\u003e\n\u003cli\u003eDry with compressed air or for 10 minutes at 50 °C. Don't exceed 10 minutes in alcohol in total.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003ePost-curing\u003c\/h4\u003e\n\u003cp\u003eQuick cure, no heat, in air: \u003cstrong\u003e20 minutes at room temperature\u003c\/strong\u003e in the \u003ca href=\"https:\/\/mrresin.es\/products\/heygears-ultracraft-cure-estacion-de-curado\"\u003eUltraCraft Cure\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch4\u003eFinishing before investing\u003c\/h4\u003e\n\u003cp\u003eRemove the supports by hand or with pliers and tweezers. Sand with 300-400 grit, then 600 and 1,000. On thin walls, start at 500-600. Remove the dust with water and wipe with a microfibre cloth and IPA. Your pattern is then ready to mount on the tree.\u003c\/p\u003e\n\n\u003ch3\u003eInvestment and burnout schedule\u003c\/h3\u003e\n\u003cp\u003eHeyGears has tested PAC10 with gypsum-bonded jewellery investments such as Certus Optima and Yihui Castino No.99 and YHR7097. Use the investment manufacturer's mixing ratio. The usual ratio is 38-40 parts water to 100 parts powder.\u003c\/p\u003e\n\u003cp\u003eStandard burnout schedule published by HeyGears for gypsum-bonded investments:\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eStage\u003c\/th\u003e\n\u003cth\u003eTemperature\u003c\/th\u003e\n\u003cth\u003eTime\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePlace the flasks in the kiln\u003c\/td\u003e\n\u003ctd\u003eRoom temperature (up to 150 °C)\u003c\/td\u003e\n\u003ctd\u003e-\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRamp\u003c\/td\u003e\n\u003ctd\u003e1.5 °C\/min to 180 °C\u003c\/td\u003e\n\u003ctd\u003e120 min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHold (dewaxing)\u003c\/td\u003e\n\u003ctd\u003e180 °C\u003c\/td\u003e\n\u003ctd\u003e60 min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRamp\u003c\/td\u003e\n\u003ctd\u003e1.5 °C\/min to 350 °C\u003c\/td\u003e\n\u003ctd\u003e120 min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHold\u003c\/td\u003e\n\u003ctd\u003e350 °C\u003c\/td\u003e\n\u003ctd\u003e120 min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRamp\u003c\/td\u003e\n\u003ctd\u003e3.6 °C\/min to 780 °C\u003c\/td\u003e\n\u003ctd\u003e120 min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHold (burnout)\u003c\/td\u003e\n\u003ctd\u003e780 °C\u003c\/td\u003e\n\u003ctd\u003e180 min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCool down\u003c\/td\u003e\n\u003ctd\u003e-2.5 °C\/min to casting temperature\u003c\/td\u003e\n\u003ctd\u003e60 min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCasting window\u003c\/td\u003e\n\u003ctd\u003eMetal casting temperature\u003c\/td\u003e\n\u003ctd\u003eApprox. 60 min\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eDuring the 180 °C hold, the sprue melts and the wax flows out of the pattern, letting air in. During the 780 °C hold, the remaining resin is eliminated from the investment. The flask then cools down to the casting temperature of your chosen metal. HeyGears warns against overheating the flasks when placing them in the kiln, to prevent cracking. For other investments or processes, get in touch with us.\u003c\/p\u003e\n\n\u003ch3\u003eSafety and handling\u003c\/h3\u003e\n\u003cp\u003eAccording to its safety data sheet, the liquid resin carries the signal word \"Warning\" and these hazard statements: H315 (causes skin irritation), H317 (may cause an allergic skin reaction) and H319 (causes serious eye irritation).\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWear gloves and safety glasses and ensure good ventilation. Avoid contact with liquid resin and with parts that are not fully cured.\u003c\/li\u003e\n\u003cli\u003eFlash point: above 250 °C, according to the safety data sheet. Not classified as dangerous goods for transport.\u003c\/li\u003e\n\u003cli\u003eStore between 15 and 28 °C, away from sunlight and moisture. Shelf life of 18 months.\u003c\/li\u003e\n\u003cli\u003eDon't pour liquid resin down the drain: cure it and dispose of it in accordance with local regulations.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWho it's not for\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAnyone with a 405 nm printer from another brand, or a Reflex RS \/ RS Turbo.\u003c\/li\u003e\n\u003cli\u003eAnyone without the Pulsing Release Module.\u003c\/li\u003e\n\u003cli\u003eEnd-use parts: it's a material designed to burn out inside the investment, not to be used as is.\u003c\/li\u003e\n\u003cli\u003eDental crowns or frameworks that require a certified material.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I use PAC10 on a 405 nm printer?\u003c\/h4\u003e\n\u003cp\u003eNo. It's a 385 nm resin only for the UltraCraft Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro. It's also not validated on the Reflex RS.\u003c\/p\u003e\n\u003ch4\u003eIs the Pulsing Release Module required?\u003c\/h4\u003e\n\u003cp\u003eYes. HeyGears states that PAC10 requires the Pulsing Release Module on all compatible printers.\u003c\/p\u003e\n\u003ch4\u003eHow much ash does it leave?\u003c\/h4\u003e\n\u003cp\u003eBetween 0.01 and 0.02 %, according to HeyGears' thermogravimetric analysis. With a correct burnout schedule, the flask is left clean.\u003c\/p\u003e\n\u003ch4\u003eWhich metals can it be cast in?\u003c\/h4\u003e\n\u003cp\u003eHeyGears presents it for jewellery and precious metals, and shows castings in silver, gold and copper.\u003c\/p\u003e\n\u003ch4\u003eWhich investment should I use?\u003c\/h4\u003e\n\u003cp\u003eGypsum-bonded jewellery investments. HeyGears has tested it with Certus Optima and with Yihui Castino No.99 and YHR7097.\u003c\/p\u003e\n\u003ch4\u003eHow is it post-cured before investing?\u003c\/h4\u003e\n\u003cp\u003e20 minutes of quick curing, without heat, in the UltraCraft Cure. Then sand if needed and remove the dust before mounting it on the tree.\u003c\/p\u003e\n\u003ch4\u003eIs it suitable for dental prosthetics?\u003c\/h4\u003e\n\u003cp\u003eHeyGears does not list it as a dental material. For dental use, we recommend dedicated materials.\u003c\/p\u003e\n\u003ch4\u003eWhere does it ship from?\u003c\/h4\u003e\n\u003cp\u003eWe ship it from our official distributor in Europe.\u003c\/p\u003e","brand":"HeyGears","offers":[{"title":"Default Title","offer_id":55384205328721,"sku":"DIST-6971437941621","price":294.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0852\/0414\/0369\/files\/resina-calcinable-heygears-pac10-joyeria-1kg.jpg?v=1792509583","url":"https:\/\/mrresin.es\/en\/products\/resina-heygears-ultraprint-casting-pac10-calcinable-1kg","provider":"Mr Resin","version":"1.0","type":"link"}