{"product_id":"resina-heygears-ultraprint-pap10-alto-detalle-1kg","title":"HeyGears UltraPrint PAP10 - High-Detail Resin for Reflex 1 kg","description":"\u003ch2\u003eHeyGears UltraPrint PAP10: high-detail resin for miniatures and fine parts\u003c\/h2\u003e\n\u003cp\u003ePAP10 is HeyGears' resin for when detail comes first: miniatures, small-scale replicas and parts with very fine structures. It comes in a 1 kg bottle and in two colours, ash grey and black. It's part of the UltraPrint range, designed for HeyGears Reflex printers: the Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro work with \u003cstrong\u003e385 nm\u003c\/strong\u003e light, and the Reflex RS and RS Turbo with \u003cstrong\u003e405 nm\u003c\/strong\u003e. HeyGears validates it on all of them with its own profiles.\u003c\/p\u003e\n\u003cp\u003eFirst, the important part: \u003cstrong\u003ethis is not a resin for generic 405 nm LCD printers\u003c\/strong\u003e (Elegoo, Anycubic, Phrozen and similar). HeyGears formulates and validates it for its Reflex platform, with locked parameters in its software. If you don't own a Reflex, this resin isn't for you.\u003c\/p\u003e\n\n\u003ch3\u003eKey points\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eWavelength:\u003c\/strong\u003e 385 nm on Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro; 405 nm on Reflex RS and RS Turbo. Only validated on HeyGears printers, not on 405 nm LCD printers from other brands.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFine detail:\u003c\/strong\u003e minimum pillar of 0.1 mm in black and 0.15 mm in ash grey; minimum embossed detail of 0.06 mm (black figure).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStability:\u003c\/strong\u003e dimensional deviation within ±0.05 mm according to HeyGears.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAgeing:\u003c\/strong\u003e 600 h of UV ageing (ASTM G154), which HeyGears equates to about 8 years of indoor use, with less than 30 % loss of properties and no noticeable colour change.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardness:\u003c\/strong\u003e 83 Shore D (ash grey) and 78 Shore D (black).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlexural strength:\u003c\/strong\u003e 93-94 MPa.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDoes not require the Pulsing Release Module.\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFormat:\u003c\/strong\u003e 1,000 g bottle.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat it's for and who it's for\u003c\/h3\u003e\n\u003cp\u003eHeyGears presents it as a high-precision application resin: end-use miniatures, small replicas and intricate parts. It's the one to put in the machine for wargaming and RPG figures, busts, small dioramas and any part with sharp edges, fine textures or thin elements such as spears, ropes or filigree.\u003c\/p\u003e\n\u003cp\u003eThe two colours have different uses:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAsh grey:\u003c\/strong\u003e the go-to colour for painting. Detail is easy to see and primer adheres well to a neutral tone. It's the one HeyGears recommends for painting and finishing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBlack:\u003c\/strong\u003e edges and textures stand out more to the naked eye, and it reaches the finest pillar (0.1 mm). Useful for parts that will stay unpainted or for presenting prototypes in black.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBeyond miniatures, its dimensional stability and ageing resistance make it suitable for short runs of small parts that need to come out identical: HeyGears talks about small-batch production with consistent results.\u003c\/p\u003e\n\n\u003ch3\u003eCompatibility: HeyGears printers and Pulsing Release Module\u003c\/h3\u003e\n\u003cp\u003ePAP10 works on HeyGears Reflex series printers, with the HeyGears Blueprint process packages. It does not require the Pulsing Release Module (PRM).\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAsh grey:\u003c\/strong\u003e Reflex, Reflex Turbo, Reflex RS, Reflex RS Turbo, Reflex 2 and Reflex 2 Pro.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBlack:\u003c\/strong\u003e the official HeyGears store lists it for Reflex, Reflex Turbo, Reflex RS and Reflex RS Turbo. HeyGears' materials website also includes it for the Reflex 2 and 2 Pro, but warns that compatibility is being updated. If you have a Reflex 2, check that the black process package appears in Blueprint before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eAbout wavelength: the Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro work at 385 nm; the Reflex RS and RS Turbo at 405 nm. HeyGears validates PAP10 on both families, always with its own profiles. That doesn't make it a resin for any 405 nm printer: outside the Reflex series there is no official profile and no guaranteed result.\u003c\/p\u003e\n\u003cp\u003eIf you use the Pulsing Release Module on a Reflex RS or RS Turbo, PAP10 is on the list of resins compatible with the RS PRM kit. Printers: \u003ca href=\"https:\/\/mrresin.es\/products\/impresora-3d-heygears-ultracraft-reflex-2-pro\"\u003eReflex 2 Pro\u003c\/a\u003e, \u003ca href=\"https:\/\/mrresin.es\/products\/impresora-3d-heygears-ultracraft-reflex-turbo\"\u003eReflex Turbo\u003c\/a\u003e and \u003ca href=\"https:\/\/mrresin.es\/products\/impresora-3d-heygears-ultracraft-reflex-rs-turbo\"\u003eReflex RS Turbo\u003c\/a\u003e. All other resin printers are in \u003ca href=\"https:\/\/mrresin.es\/collections\/impresoras-3d-resina\"\u003eresin 3D printers\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical specifications\u003c\/h3\u003e\n\u003cp\u003eData from the HeyGears technical data sheet (TDS), rev. 02.2025. These are average laboratory values with a deviation of ±10 %.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eProperty\u003c\/th\u003e\n\u003cth\u003eStandard\u003c\/th\u003e\n\u003cth\u003eAsh grey\u003c\/th\u003e\n\u003cth\u003eBlack\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eImpact strength (notched)\u003c\/td\u003e\n\u003ctd\u003eASTM D256\u003c\/td\u003e\n\u003ctd\u003e36 J\/m\u003c\/td\u003e\n\u003ctd\u003e31 J\/m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eElongation at break\u003c\/td\u003e\n\u003ctd\u003eASTM D638\u003c\/td\u003e\n\u003ctd\u003e12 %\u003c\/td\u003e\n\u003ctd\u003e12 %\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWork of fracture\u003c\/td\u003e\n\u003ctd\u003eISO 20795-1\u003c\/td\u003e\n\u003ctd\u003e3,050 J\/m²\u003c\/td\u003e\n\u003ctd\u003e2,370 J\/m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTensile modulus\u003c\/td\u003e\n\u003ctd\u003eASTM D638\u003c\/td\u003e\n\u003ctd\u003e1,750 MPa\u003c\/td\u003e\n\u003ctd\u003e1,750 MPa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFlexural modulus\u003c\/td\u003e\n\u003ctd\u003eASTM D790\u003c\/td\u003e\n\u003ctd\u003e1,920 MPa\u003c\/td\u003e\n\u003ctd\u003e2,490 MPa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTensile strength\u003c\/td\u003e\n\u003ctd\u003eASTM D638\u003c\/td\u003e\n\u003ctd\u003e54 MPa\u003c\/td\u003e\n\u003ctd\u003e55 MPa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFlexural strength\u003c\/td\u003e\n\u003ctd\u003eASTM D790\u003c\/td\u003e\n\u003ctd\u003e93 MPa\u003c\/td\u003e\n\u003ctd\u003e94 MPa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHeat deflection temperature (0.455 MPa)\u003c\/td\u003e\n\u003ctd\u003eASTM D648\u003c\/td\u003e\n\u003ctd\u003e58 °C\u003c\/td\u003e\n\u003ctd\u003e58 °C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHardness\u003c\/td\u003e\n\u003ctd\u003eASTM D2240\u003c\/td\u003e\n\u003ctd\u003e83 Shore D\u003c\/td\u003e\n\u003ctd\u003e78 Shore D\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater absorption\u003c\/td\u003e\n\u003ctd\u003eASTM D570\u003c\/td\u003e\n\u003ctd\u003e1 %\u003c\/td\u003e\n\u003ctd\u003e1 %\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eViscosity\u003c\/td\u003e\n\u003ctd\u003eASTM D4212\u003c\/td\u003e\n\u003ctd\u003e385 mPa·s\u003c\/td\u003e\n\u003ctd\u003e500 mPa·s\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eUV ageing\u003c\/td\u003e\n\u003ctd\u003eASTM G154\u003c\/td\u003e\n\u003ctd\u003e600 h\u003c\/td\u003e\n\u003ctd\u003e600 h\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAccelerated thermal ageing\u003c\/td\u003e\n\u003ctd\u003eYY\/T 0681.1\u003c\/td\u003e\n\u003ctd\u003e1,600 h\u003c\/td\u003e\n\u003ctd\u003e1,600 h\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eWavelength:\u003c\/strong\u003e 385 nm (Reflex, Reflex Turbo, Reflex 2\/2 Pro) and 405 nm (Reflex RS\/RS Turbo), always with HeyGears profiles.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlash point:\u003c\/strong\u003e 101 °C (safety data sheet).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDensity:\u003c\/strong\u003e 1.0-1.5 g\/cm³ at 25 °C (safety data sheet).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDamp heat test:\u003c\/strong\u003e IEC 60068-2-78 passed according to the TDS.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eUse and post-processing\u003c\/h3\u003e\n\u003cp\u003eHeyGears doesn't publish exposure or post-curing times in the technical data sheet: the parameters are in the HeyGears Blueprint process packages, which you select when preparing the job. That's how the whole UltraPrint range works: you don't have to calibrate the resin yourself.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBefore printing:\u003c\/strong\u003e shake the bottle well. The resin performs better when warm; HeyGears actually uses PAP10 to benchmark the heated scraper on the Reflex 2, which brings it from 10 to 22 °C in 6 minutes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWashing:\u003c\/strong\u003e remove uncured resin with the solvent specified in the process package. With the Reflex range, the most convenient option is the \u003ca href=\"https:\/\/mrresin.es\/products\/heygears-ultracraft-wash-estacion-de-lavado\"\u003eUltraCraft Wash\u003c\/a\u003e; if you wash by hand, you'll find alcohol and accessories in \u003ca href=\"https:\/\/mrresin.es\/collections\/alcohol-y-postprocesado\"\u003ealcohol and post-processing\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePost-curing:\u003c\/strong\u003e HeyGears offers its \u003ca href=\"https:\/\/mrresin.es\/products\/heygears-ultracraft-cure-estacion-de-curado\"\u003eUltraCraft Cure\u003c\/a\u003e, with dual-wavelength curing and heat, designed for the Reflex platform. Other stations are in \u003ca href=\"https:\/\/mrresin.es\/collections\/maquinas-lavado-curado-wash-cure\"\u003ewash and cure machines\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePainting:\u003c\/strong\u003e with ash grey, prime directly after curing and give the support marks a light sanding.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSafety and handling\u003c\/h3\u003e\n\u003cp\u003eThe HeyGears safety data sheet (SDS) classifies PAP10 with the signal word \"Warning\" and the following hazard statements:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eH302: harmful if swallowed.\u003c\/li\u003e\n\u003cli\u003eH315: causes skin irritation.\u003c\/li\u003e\n\u003cli\u003eH317: may cause an allergic skin reaction.\u003c\/li\u003e\n\u003cli\u003eH319: causes serious eye irritation.\u003c\/li\u003e\n\u003cli\u003eH335: may cause respiratory irritation.\u003c\/li\u003e\n\u003cli\u003eH373: may cause damage to organs through prolonged or repeated exposure.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWork with nitrile gloves, safety glasses and good ventilation. If resin gets on your skin, wash with soap and water. Keep the bottle closed in a cool, dry, ventilated place, away from heat and out of reach of children. Don't pour liquid resin down the drain: cure it in sunlight or with UV and dispose of it as solid waste in accordance with local regulations.\u003c\/p\u003e\n\n\u003ch3\u003eWhich one should you choose?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePAP10\u003c\/strong\u003e: maximum detail and stability for miniatures and small parts.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/mrresin.es\/products\/resina-heygears-ultraprint-pas10-estandar-1kg\"\u003ePAS10\u003c\/a\u003e: standard modelling resin, for everyday printing and prototypes that don't demand as much detail.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/mrresin.es\/products\/resina-heygears-ultraprint-pawr10-resistente-al-desgaste-1kg\"\u003ePAWR10\u003c\/a\u003e: if the part will be handled a lot (board games, articulated figures, gears), thanks to its 2H surface hardness and higher impact strength (64 J\/m).\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/mrresin.es\/products\/resina-heygears-ultraprint-paf10-flexible-1kg\"\u003ePAF10\u003c\/a\u003e: PVC-like miniatures that need to survive drops and bending.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/mrresin.es\/products\/resina-heygears-ultraprint-pau11-tipo-abs-1kg\"\u003ePAU11\u003c\/a\u003e: if you're after ABS-like behaviour for functional parts.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eYou'll find all our resins in \u003ca href=\"https:\/\/mrresin.es\/collections\/resinas\"\u003e3D printer resins\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eWho it's not for\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAnyone with a 405 nm LCD printer from another brand. There's no official profile and we don't recommend it.\u003c\/li\u003e\n\u003cli\u003eParts that need to bend or snap-fit: with 12 % elongation, it's a rigid resin.\u003c\/li\u003e\n\u003cli\u003eParts exposed to heat: its heat deflection temperature is 58 °C.\u003c\/li\u003e\n\u003cli\u003eLarge, solid parts where detail doesn't matter: there are cheaper resins for that.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eDoes PAP10 work on my Elegoo, Anycubic or Phrozen printer?\u003c\/h4\u003e\n\u003cp\u003eWe don't sell it for that. PAP10 is formulated for HeyGears Reflex printers (385 nm, and 405 nm on the RS and RS Turbo) and is printed with the HeyGears Blueprint process packages. There are no official parameters for generic 405 nm LCD printers.\u003c\/p\u003e\n\u003ch4\u003eIs it a 385 nm or a 405 nm resin?\u003c\/h4\u003e\n\u003cp\u003eBoth, but only within the HeyGears range. The Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro cure it at 385 nm; the Reflex RS and RS Turbo at 405 nm. In both cases with HeyGears Blueprint profiles. The fact that it works on an RS at 405 nm doesn't mean it works on any 405 nm printer.\u003c\/p\u003e\n\u003ch4\u003eDoes it need the Pulsing Release Module?\u003c\/h4\u003e\n\u003cp\u003eNo. It prints with the standard vat. If you already have the PRM on a Reflex RS or RS Turbo, PAP10 is among the resins compatible with that kit.\u003c\/p\u003e\n\u003ch4\u003eWhat's the difference between ash grey and black?\u003c\/h4\u003e\n\u003cp\u003eAsh grey is easier to paint, slightly harder (83 vs 78 Shore D) and tougher on impact. Black defines edges more sharply and reaches 0.1 mm pillars, versus 0.15 mm for grey.\u003c\/p\u003e\n\u003ch4\u003eDoes the black work on the Reflex 2?\u003c\/h4\u003e\n\u003cp\u003eHeyGears' materials website lists it as compatible, but the official store only lists it for Reflex, Reflex Turbo, RS and RS Turbo, and HeyGears warns that it's updating compatibility. Check in Blueprint whether you have the black process package before ordering. Ash grey is listed as compatible with the Reflex 2 in every source.\u003c\/p\u003e\n\u003ch4\u003eHow long does a part printed in PAP10 last?\u003c\/h4\u003e\n\u003cp\u003eHeyGears has subjected it to 600 h of UV ageing, which it equates to about 8 years indoors or 1 year outdoors, with less than 30 % loss of properties, no noticeable colour change and a dimensional deviation of ±0.1 mm.\u003c\/p\u003e\n\u003ch4\u003eWhere are the exposure and curing times?\u003c\/h4\u003e\n\u003cp\u003eIn the HeyGears Blueprint process packages. HeyGears doesn't publish them in the technical data sheet because the printer and software apply them directly.\u003c\/p\u003e\n\u003ch4\u003eIs it suitable for functional parts?\u003c\/h4\u003e\n\u003cp\u003eFor small, rigid parts, yes: 54-55 MPa tensile and 93-94 MPa flexural strength. For parts that will take knocks or friction, PAWR10 is a better choice.\u003c\/p\u003e","brand":"HeyGears","offers":[{"title":"Ash grey","offer_id":55384207884625,"sku":"DIST-6971437941584","price":57.99,"currency_code":"EUR","in_stock":true},{"title":"Black","offer_id":55384207917393,"sku":"DIST-6971437942185","price":57.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0852\/0414\/0369\/files\/resina-heygears-ultraprint-pap10-gris-ceniza-1kg.jpg?v=1792509648","url":"https:\/\/mrresin.es\/en\/products\/resina-heygears-ultraprint-pap10-alto-detalle-1kg","provider":"Mr Resin","version":"1.0","type":"link"}