Anycubic Water Washable 2.0: Complete Guide 2026 | Mr Resin 💧

If you've landed here, chances are you know the feeling: you love resin 3D printing, but dealing with isopropyl alcohol (IPA) puts you off. The smell, the risk of keeping a flammable liquid at home, the cost... it's a real hassle! 😩 What if you could skip all that and clean your prints with just water?

That's exactly the promise of the Anycubic Water Washable 2.0 resin for just €20.99 — simple and powerful. It's an Anycubic resin for 3D printers designed for beginners and home users alike. It's the perfect choice if you want an easy, safe, low-odour workflow. Let's find out if it really lives up to the hype.

What is Anycubic Water Washable 2.0 Resin? 🤔

Think of standard resin like oil — it simply doesn't mix with water, which is why you need a solvent like alcohol to clean it. Anycubic Water Washable 2.0 works differently. Its formula contains special hydrophilic compounds that make it water-friendly. 🤝💧

This means that once your print is done, you can rinse it straight under the tap. The water washes away the uncured liquid resin, leaving your model clean and ready to cure. It really is that straightforward!

What's New in Version 2.0 vs. 1.0?

The "2.0" isn't just a marketing label. Anycubic listened to community feedback and addressed the weak points of the original version:

• Better bed adhesion: Far fewer failed prints — parts now stick much more reliably.
• Works at 15–20°C: No more needing a warm room to get good results.
• Less brittle: Finished prints are noticeably more durable.

These improvements make working with Anycubic resins a much more consistent experience, especially if you're just starting out.

Step-by-Step Wash Process 💧

Cleaning your prints with this resin is a breeze. No specialist chemical gloves, no forced ventilation — it's much easier than you'd expect!

What you'll need:

• A couple of containers filled with water (food storage containers work great).
• An old toothbrush or a soft-bristle brush.
• Nitrile gloves (uncured resin is still a chemical).
• Paper towels for drying.

Let's get into it — just follow these 5 steps:

1. Remove the print from the build plate: Carefully use your spatula to detach your print. Take it slow to avoid any damage.
2. First wash (the dirty one): Submerge the print in the first container of water and swirl it around for 1-2 minutes. You'll see the water turn cloudy almost immediately. This step gets rid of the bulk of the uncured resin!
3. Second wash (the detail wash): Transfer the print to the second container of clean water. Now use a soft brush to gently scrub every corner and fine detail. This is where you get that perfect finish. ✨
4. Drying: This step is critical! Thoroughly dry the print with paper towels or an air blower. There should be absolutely no water left, especially inside any hollow areas, or the print may crack during curing.
5. Curing: Once your print is clean and dry, place it in your UV curing station or leave it in direct sunlight. Within a few minutes it will fully harden and be ready to use.

IMPORTANT! What do I do with the dirty water? 🌍 Never pour it down the drain. Resin is toxic to the environment. The solution is simple: leave the container out in sunlight for a few hours. The UV light will cure the resin residue, causing it to solidify. You can then filter the water and dispose of the hardened plastic bits in your regular household waste. Easy!

Anycubic Water Washable 2.0 – Pros 👍

Why has this resin become so popular? Here's why:

• Near-odourless: Perfect for printing in a flat or bedroom without bothering anyone around you. Your nose will thank you. 👃
• Safer to use: No isopropyl alcohol means no flammable liquids in your home. Greater peace of mind for you and your family.
• Cost-effective: Although the bottle costs slightly more upfront, you'll save money by not repeatedly buying litres of IPA. It pays for itself over time. 💰
• Great for beginners: It simplifies the whole workflow so much that it takes the fear out of getting started. Less frustration, more fun!
• Wide colour range: Plenty of options to bring your prints to life.
• Better adhesion: Version 2.0 has dramatically reduced print failures thanks to improved first-layer adhesion.

Do these benefits convince you? Give it a try and see the difference for yourself. Check out the Water Washable 2.0 and start printing the cleaner, simpler way.

Limitations and Cons of This Resin 👎

Nothing is perfect. It's important to know the downsides too, so you can decide whether it's the right choice for you:

• Less durable: Parts are somewhat more brittle than those made with standard resin. Not the best choice for functional parts or anything that needs to withstand impacts.
• Not for mechanical parts: If you need gears, brackets, or housings that can take a beating, you're better off going with an ABS-like resin.
• Slightly higher price: The bottle costs a little more than standard resin.
• Wastewater needs proper disposal: You can't pour it down the drain, as we've already covered. It requires one small extra step.
• Not for maximum detail: If you're chasing the sharpest possible definition for painting competitions, a dedicated high-detail resin will give you better results.

Comparison: Water Washable vs. Standard V2 🥊

To make things crystal clear, here's a straight-to-the-point comparison table.

Verdict: When should you choose each one?

• Choose Water Washable 2.0 if: Convenience, low odour, and safety are your top priorities. Perfect for printing miniatures and decorative figures at home without the hassle.
• Choose Standard Resin V2 if: You want the lowest price possible and don't mind the alcohol wash process. It's a reliable workhorse for all kinds of projects.

Available colours: a rainbow of options! 🎨

One of the best things about Anycubic Water Washable 2.0 is the range of colours on offer. With 11 options to choose from, you're sure to find the perfect one for your project.

The available colours are:

• Opaque: Black, White, Grey, Purple, HD Grey.
• Translucent: Red, Blue, Green, Yellow.
• Special: Smoke Grey, Clear.

Which colour should beginners start with? We recommend starting with Grey. Why? Because grey shows fine details and any imperfections most clearly, making it easier to dial in your printer settings and get up to speed faster. Translucent colours are great for light-through effects, while opaques give a solid, professional finish. Don't be afraid to experiment!

Browse the full Anycubic Water Wash Resin 2.0 colour range here

Tips for the Best Results ✨

Get the most out of your resin with these handy tips:

1. Shake the bottle well: Before every use, shake the bottle for at least one minute. Resin components tend to settle and separate, so a good shake ensures a consistent, even mix.
2. Use the right exposure settings: Don't guess. Look up exposure setting charts for your specific printer model and this resin. Starting with the correct parameters will save you a lot of failed prints. Check out our blog for an Anycubic resin exposure settings guide.
3. Watch the temperature: Try to keep your room above 15°C. While the V2 formula has improved significantly, resin still performs best when it's warm.
4. Don't over-cure: Too much UV light can cause prints to yellow and become brittle. Stick to the recommended cure times.
5. Watch out for trapped water: If your print has hollow sections, make sure to add drain holes. Water trapped inside during curing can cause the print to crack or explode!

Who Is This Resin Best For? 🤔

Here's a quick breakdown to help you decide.

✅ This resin is perfect for you if:

• You're a beginner who wants a straightforward printing experience.
• You print in a flat or at home and need low odour.
• You print miniatures and decorative figures.
• You prioritise convenience and safety above all else.

❌ You might want a different resin if:

• You need strong, functional parts (gears, brackets, etc.).
• You want the highest possible detail for competition-level prints.
• You're printing mechanical parts that will be under stress.

```

FAQ: Frequently Asked Questions

1. Can you use tap water? Yes! That's the whole point. No extra cleaning supplies needed. If your tap water is very hard, a final rinse with distilled water can improve the surface finish, but it's not essential.

2. Is it really low odour? Compared to standard resin cleaned with IPA, the smell is minimal — barely noticeable for most people. That said, always ventilate your workspace for safety.

3. Does it work with Elegoo or Creality printers? Absolutely. It's compatible with most 405nm LCD/SLA resin 3D printers on the market, including Elegoo, Creality, Phrozen, and more.

4. Are the prints waterproof after curing? Absolutely. Once cured, the print is a solid plastic that is completely waterproof. The "washable" property only applies when the resin is still in its liquid state.

5. Can I mix it with standard resin? No. Don't do it. They have different chemistries and the results will be a disaster. Keep each resin in its own vat!

Verdict: Is this the right resin for you? 🚀

Anycubic Water Washable 2.0 is a fantastic resin that removes the biggest barriers to getting started with 3D printing: the smell, the cost, and the hassle of isopropyl alcohol.

It's the perfect choice if you value convenience and want a clean, safe workflow — especially if you're printing at home. It lets you focus on the fun part: creating!

Ready to try 3D printing the easy way? Head over to our store and browse our full range of Anycubic resins.

And before you go, join our Telegram community. You'll find exclusive discounts, coupons, news, and events waiting for you. Oh, and don't forget to subscribe to our Newsletter so you never miss a deal.

✨ Happy Printing! 🚀