HeyGears UltraPrint PAWR10: wear-resistant resin for parts that get handled
PAWR10 is HeyGears' resin for parts that will pass through many hands: board game tokens and figures, articulated models, BJD dolls, electronics accessories, gears and outdoor gear. Its strong point is the surface: 2H pencil hardness, which HeyGears compares to car paint, and a smooth finish straight off the printer. 1 kg bottle, in cream and cream yellow.
It is an UltraPrint resin for HeyGears Reflex printers: 385 nm on the Reflex, Reflex Turbo, Reflex 2 and 2 Pro, and 405 nm on the Reflex RS and RS Turbo. It is not for generic 405 nm LCD printers (Elegoo, Anycubic, Phrozen...). Without a Reflex, there's no point in buying it.
Key features
-
Wavelength: 385 nm on the Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro; 405 nm on the Reflex RS and RS Turbo. Only validated on HeyGears printers, not on 405 nm LCD printers from other brands.
-
2H surface hardness (GB/T 6739 pencil test): scratch-resistant.
-
Notched impact: 64 J/m, almost double that of PAP10 (31-36 J/m) or PAU20 (35 J/m).
-
Smooth surface: HeyGears describes a finish similar to a part sanded with 600 to 1000 grit.
-
No dust from friction: the TDS states it does not shed dust under high-speed friction.
-
Resistant to yellowing and to loss of properties over time.
- Does not require the Pulsing Release Module.
-
Format: 1,000 g bottle.
What it's for and who it's for
A display miniature doesn't take any punishment. A board game figure, an articulated part or a housing that gets assembled and disassembled does: rubbing, knocks against the table, fingernails, other parts. PAWR10 is made for exactly that. It combines high surface hardness (2H) with more toughness than a detail resin, so the part withstands use without scratching or chipping right away.
Uses suggested by HeyGears:
- Board game and wargame figures and tokens that are handled every game.
- Models with moving parts and BJDs (ball-jointed dolls), where the joints rub against each other.
- Consumer electronics accessories.
- Gears and contact parts.
- Outdoor gear.
Both colours are light shades that are easy to paint. HeyGears describes it as an easy-to-paint resin, and in cream it also looks good unpainted on functional parts.
Compatibility: HeyGears printers and Pulsing Release Module
According to HeyGears, PAWR10 is compatible with the Reflex, Reflex Turbo, Reflex RS, Reflex RS Turbo, Reflex 2 and Reflex 2 Pro, using the HeyGears Blueprint process packages. It does not require the Pulsing Release Module (PRM).
About the light source: the Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro work at 385 nm; the Reflex RS and RS Turbo at 405 nm. HeyGears validates it on both families with its own profiles. That doesn't make it suitable for other 405 nm printers: outside the Reflex series there is no official profile.
If you have the PRM on a Reflex RS or RS Turbo, PAWR10 is on the kit's list of compatible resins. Compatible printers in our shop: Reflex 2 Pro, Reflex Turbo and Reflex RS Turbo. More models in resin 3D printers.
Technical specifications
Data from the HeyGears technical data sheet (TDS), rev. 02.2025. Average laboratory values with a deviation of ±10 %.
| Property |
Standard |
Value |
| Pencil hardness |
GB/T 6739 |
2H |
| Impact strength (notched) |
ASTM D256 |
64 J/m |
| Elongation at break |
ASTM D638 |
20 % |
| Work of fracture |
ISO 20795-1 |
4,300 J/m² |
| Tensile modulus |
ASTM D638 |
1,290 MPa |
| Flexural modulus |
ASTM D790 |
1,300 MPa |
| Tensile strength |
ASTM D638 |
34 MPa |
| Flexural strength |
ASTM D790 |
58 MPa |
| Heat deflection temperature (0.455 MPa) |
ASTM D648 |
52 °C |
| Hardness |
ASTM D2240 |
81 Shore D |
| Water absorption |
ASTM D570 |
2.5 % |
| Viscosity |
ASTM D4212 |
373 mPa·s |
| UV ageing |
- |
200 h |
| Accelerated thermal ageing |
YY/T 0681.1 |
1,600 h |
-
Wavelength: 385 nm (Reflex, Reflex Turbo, Reflex 2/2 Pro) and 405 nm (Reflex RS/RS Turbo), always with HeyGears profiles.
-
Colours: cream and cream yellow. Same technical data.
-
Flash point: 106 °C (safety data sheet).
-
Density: 1.0-1.5 g/cm³ at 25 °C (safety data sheet).
-
Ageing: HeyGears equates its test to about 3 years indoors, with less than 30 % loss of properties, no noticeable colour change and a deviation of ±0.1 mm.
Use and post-processing
Exposure and curing times are not in the technical data sheet: they come in the HeyGears Blueprint process packages. You select PAWR10 when preparing the print and the Reflex applies the parameters. You don't need to calibrate the resin.
-
Before printing: shake the bottle. At 373 mPa·s it's a free-flowing resin that's easy to handle.
-
Washing: use the solvent specified in the process package. With the UltraCraft Wash, washing involves almost no contact with the resin. For manual washing, see alcohol and post-processing.
-
Post-curing: the UltraCraft Cure is HeyGears' station for the Reflex platform, with dual-wavelength UV and heat. More options in wash and cure machines.
-
Articulated parts: leave clearance in the joints. Friction resistance is no substitute for well-set tolerances in the design.
Safety and handling
The HeyGears safety data sheet (SDS) classifies it with the signal word "Warning" and these hazard statements:
- H302: harmful if swallowed.
- H315: causes skin irritation.
- H317: may cause an allergic skin reaction.
- H319: causes serious eye irritation.
- H335: may cause respiratory irritation.
- H373: may cause damage to organs through prolonged or repeated exposure.
Always use nitrile gloves, safety glasses and ventilation. If it gets on your skin, wash with soap and water. Keep the bottle closed in a cool, dry, ventilated place, away from heat sources. Liquid resin must not go down the drain: cure it and dispose of it according to local regulations.
Which one should you choose?
-
PAWR10: functional parts that get touched, rubbed or knocked. Prioritises surface and impact resistance.
-
PAP10: finer detail (0.1-0.15 mm pillars) and more rigidity, for display miniatures.
-
PAF10: if the part needs to bend without breaking (46 % elongation in volcanic grey).
-
PAU20: structural parts and load-bearing jigs and fixtures, with 69 MPa tensile strength. Requires the Pulsing Release Module.
-
PAS10: standard resin for prototypes and models without demanding use requirements.
More technical resins in engineering resins.
Who it's not for
- For 405 nm LCD printers from other brands.
- For parts exposed to heat: heat deflection at 52 °C.
- For parts in prolonged contact with water: it absorbs 2.5 %, more than other resins in the range.
- For flexible or elastic parts: it's a rigid, tough resin and doesn't bend.
Frequently asked questions
Can I use PAWR10 on a printer that isn't a HeyGears?
We don't sell it for that. It's a resin for the HeyGears Reflex series (385 nm, and 405 nm on the RS and RS Turbo), with parameters in HeyGears Blueprint. There are no official profiles for generic 405 nm LCD printers.
Is it a 385 nm or a 405 nm resin?
Both, but only within the HeyGears range. The Reflex, Reflex Turbo, Reflex 2 and Reflex 2 Pro cure it at 385 nm; the Reflex RS and RS Turbo at 405 nm. In both cases with HeyGears Blueprint profiles. The fact that it works on an RS at 405 nm doesn't mean it works on any 405 nm printer.
Does it need the Pulsing Release Module?
No. It works with the standard vat. If you have the PRM on a Reflex RS or RS Turbo, it's compatible too.
What does 2H hardness mean?
It's the result of the pencil hardness test (GB/T 6739): a 2H pencil doesn't scratch the surface. HeyGears compares it to the hardness of car paint.
What's the difference between cream and cream yellow?
Only the colour. The technical data sheet and safety data sheet are the same for both.
Is it suitable for BJD dolls and articulated figures?
Yes, HeyGears recommends it for BJD dolls and moving models because of its wear resistance and because it doesn't shed dust from friction.
Does it yellow over time?
HeyGears presents it as resistant to yellowing. After its ageing test, equivalent to about 3 years indoors, the colour change is not noticeable (ΔE less than 2).
Can it be painted?
Yes. HeyGears describes it as easy to paint, and both light shades take primer well.